Related topics

Startup failure
To repair NT kernel boot strapping problems you use recovery console fixmbr, fixboot, and/or bootcfg commands depending on need. distinguishable from magic is insufficiently advanced. http://www.dts-l.org http://support.microsoft. com/servicedesks/fileversion/default.asp "Danny" <PokeMyHon...@hotmail.com> wrote

Installing Windows XP Pro
That's the reason for the suggestion to edit C:\boot.ini; this is the file that "points to" the boot folder (\Windows, by default) in some partition on some use other editing tools, such as booting to MS-DOS on a floppy diskette or - much better - by booting to the WinXP Recovery Console from the WinXP CD-ROM.

inaccessible_boot_device after SP3 - help !!!
Some helpful recovery console MSKB articles are listed below: Description of the Windows 2000 Recovery console: http://support.microsoft.com/default.aspx?scid=kb;en-us;Q229716 Installing the Windows 2000 revocery console: http://support.microsoft.com/default. aspx?scid=kb;en-us;Q216417 Installation and use of the

Can't run/install Microsoft Recovery Console
NOTE: Make sure you delete correct line nad "recovery console " is not listed as Default. Maybe backup file before editing. NOTE: This ONLY removes dual boot My Problem is how to start the Windows normally as it was before installing it! Maybe i have to edit a .bat or .sys file??? Or there is an option in the

Keyboard missing after application installing interrupt and reboot
To repair a Windows XP installation using Recovery Console, press R. To quit Setup without installing Windows XP, press F3. Press ENTER. I then booted the XP Home CD and choose the "Fix" option and then selected my default install at C:\Windows. This went into a blue screen as well.

Installing Programs take way 2 long
One of the annoyances of Recovery Console is the limited access one has in the default configuration. In order to fully access your hard drive in Recovery Console you have to make a local policy change first, then load some environmental variables. http://support.microsoft.com/default.aspx?scid=kb;[LN];Q235364 Of

URGENT -- XP Home vs XP Pro - Recovery Console
I've installed the HPT 366 Drivers without issue, I've even gone as far as diabling the HPT and installing a Promise controller, removing the NIC, Pulling out the Video Card and installing Press C to run the Recovery Console tool. Select the installation that you want to repair. Type the administrator password.

Can't boot after installing blaster worm patch
I've tried every possible options and non works... is there a default or a way to bypass or disable this option through settings??? is there a way to If you have the recovery console installed you could try deleting the passthru driver, this *might* get rid of your problem, or it *might* make things worse,

registry corrupted
Also used Recovery Console to disable some services, no progress yet. Anyone could help me? Thanks very much for your time and assistance! Screen on Reboot After Installing Corel CD Creator 2.0 (Q154915)" http://support.microsoft.com/default.aspx?scid=kb;EN-US;Q237468 "Windows 2000 May Display an Error Message

Installing Recovery Console after installing SP2
How do I suppress any dialog boxes when installing the Recovery Console? winnt32 /cmdcons /unattend References HOW TO: Install the Windows Recovery Console http://support.microsoft.com/default.aspx?scid=kb;en-us;216417 -- Ritchie Keywords: ggcmdcons ggsilent gginstall.

XP sucessfully installed, would not re-boot after installing ...
To set up Windows XP now, press ENTER * To repair a Windows XP installation using Recovery Console, press R. * To quit Setup without installing Windows XP, press F3. copy c:\windows\repair\default c:\windows\system32\config\default 7) Type "exit" (without the quotation marks) to quit Recovery Console.

recovery console access
Bjorn Landemoo bj...@landemoo.com microsoft public win2000 general François My guess is that an american code page is used by the recovery console, while you might have another code page as default in Win2000. I haven't found any way to change this behavior, though. Best regards Bjorn -- Bjorn Landemoo

Change Boot.ini with Recovery Console? - Win2000 Pro Setup
DSPatrick.com microsoft public win2000 setup You can replace the file from the recovery console. If it's a new install, easiest to blow it away and start a new install. http://support.microsoft.com/default.aspx?scid=kb;en-us;Q101096 To start the Recovery Console, start the computer from the Windows 2000 Setup CD or

Here are the steps to install Win 98 AFTER installing Win XP
So I could not boot to the recovery console to try to resolve the issue. I only have copies of Pro, so I could not boot to the recovery console with them. NOTE: In Windows XP Home Edition, the administrator password is blank by default. 5. At the command prompt, type the following command, and then press ENTER:

System Restore problem
Dave, The boot.ini for Windows 2000 Pro on the 3rd partition is: [boot loader] timeout=30 default=multi(0)disk(0)rdisk(0)partition(1)\WINNT [operating systems] How do I disable Norton in recovery console so I can copy boot.ini to floppy and fix in notepad? Do I need to change attributes on boot.ini?

Windows won't boot after installing latest XP security updates
I am working on your suggestion and creating the boot disk, I did also find this article: http://support.microsoft.com/default.aspx?scid=kb;en- us Then try booting the recovery console and from a command prompt issue the command; fixboot To start the Recovery Console, start the computer from the Windows 2003

problem after installing updates
... http://support.microsoft.com/default.aspx?scid=kb;en-us;828930 -- Regards, Dave Patrick ....Please no email replies - reply in newsgroup. Microsoft Certified Professional Microsoft MVP [Windows] http://www.microsoft.com/protect "Jan-Bert" wrote: How do i install the recovery console after installing windows

Installing/Repairing Win2K
To repair a Windows XP installation using Recovery Console, press R. To quit Setup without installing Windows XP, press F3. Press ENTER. Press F8 to accept the Licensing Agreement. A box lists your current Windows XP installation, and then the system prompts you to select one of the following options: To repair the

Installing Win 2003 the Drive Letters Switched, Please Help!!
229716 Description of the Windows 2000 Recovery Console http://support.microsoft. com/?id=229716 This will return servers to being vulnerable to the weakness described on Windows Update. Larry Wazny wrote: -----Original Message----- After installing the 3 most recent security patches through the Windows Update

Boot Failure
After installing XP the latter's boot loader should present the two OS to choose from when you reboot. Except you have used two separate disks and possibly the boot loader is corrupt. First from with in Windows XP install the Recovery Console as a boot option. Put the XP CD in your default optical drive and then